Vehicle Standard (Australian Design Rule 79/04 — Emission Control for Light Vehicles) 2011

made under   Section 12 of the Road Vehicle Standards Act 2018 

Compilation: 2 (up to and including Vehicle Standard (Australian Design Rule) Amendment Instrument 2021 (No.2)) 

Compilation Date: 30/11/2021

Volume 1 contains Clauses 0.1-6 and the Compilation Notes

Volume 2 contains Appendix A

Compiled by: Vehicle Safety Policy and Partnerships, Department of Infrastructure, Transport, Regional Development and Communications

CONTENTS

0.1 NAME OF STANDARD.....................................3

0.2 COMMENCEMENT........................................3

1. SCOPE.................................................3

2. applicability and implementation................................3

3. DEFINITIONS............................................3

4. REQUIREMENTS.........................................3

5. EXEMPTIONS AND ALTERNATIVE PROCEDURES................3

6. ALTERNATIVE STANDARDS................................6

COMPILATION NOTES........................................7

APPENDIX A.........................................VOLUME 2

0.1   NAME OF STANDARD [see Note 1]

0.1.1 This Standard is the Vehicle Standard (Australian Design Rule 79/04 — Emission Control for Light Vehicles) 2011.

0.1.2  This Standard may also be cited as ADR 79/04.

0.2   COMMENCEMENT [see Note 1]

0.2.1  This Standard commences on the day after it is registered.

1. SCOPE
   1.                                  This vehicle standard prescribes the exhaust and evaporative emissions requirements for light vehicles in order to reduce air pollution.
2. APPLICABILITY AND IMPLeMENTATION
   1.                                  This vehicle standard is applicable to all M and N category vehicles with a Gross Vehicle Mass less than or equal to 3.5 tonnes, notwithstanding the reference mass provisions of paragraph 1.1 of Appendix A.
   2.                                  This vehicle standard applies from 1 November 2016 in relation to vehicles produced with a ‘Date of Manufacture’ on or after 1 November 2016.
   3.                                  To the extent of any inconsistency, the applicability date specified in clause 2.2 applies in lieu of any dates specified in Appendix A.
3. DEFINITIONS
   1.                                  For the purposes of clause 2.2, ‘date of manufacture’ means, for a road vehicle entered onto the Register of Approved Vehicles under the Road Vehicle Standards Act 2018, the date of that entry. Otherwise, the date the vehicle is available in Australia in a condition that will enable an ‘Identification Plate’ to be lawfully affixed to the vehicle.
4. REQUIREMENTS
   1.                                  Vehicles which comply with the emissions limits and technical requirements of Appendix A, including all the applicable tests specified in paragraph 5.2 of Appendix A, and as varied by Part 5 of this vehicle standard, will be accepted as complying with this vehicle standard.
5. EXEMPTIONS AND ALTERNATIVE PROCEDURES
   1.                                  The following provisions of Appendix A do not apply to this vehicle standard:

Section 3 Application for Approval

Section 4 Approval

Section 6 Modifications of the vehicle type

Section 8 Conformity of production

Section 9 In-service conformity

Section 10 Penalties for non-conformity of production

Section 11 Production definitely discontinued

Section 12 Transitional provisions

Section 13 Names and addresses of technical services responsible for conducting approval tests, and of administrative departments

Appendix 1 Procedure for verifying the conformity of production requirements if the production standard deviation given by the manufacturer is satisfactory

Appendix 2 Procedure for verifying the conformity of production requirements if the production standard deviation given by the manufacturer is either not satisfactory or not available

Appendix 3 In-service conformity check

Appendix 4 Statistical procedure for in-service conformity check

Appendix 5 Responsibilities for in service conformity

Annex 1 Engine and vehicle characteristics and information concerning the conduct of tests

Annex 2 Communication

Annex 3 Arrangements of the Approval Mark

5.2.                                    In section 5 of Appendix A, the entire text regarding small volume manufacturers immediately following the heading “5.  Specifications and tests” is deleted.

5.3.                                    Notwithstanding that Section 8 and 9 and Appendices 1, 2, 3, 4 and 5 of Appendix A have been declared not applicable in clause 5.1 of this vehicle standard, the requirements and procedures set out in these appendices are deemed acceptable for the purposes of demonstrating compliance with the conformity requirements of this vehicle standard.

5.4.                                    For the purposes of the Type VI test specified in paragraph 5.3.5 of Appendix A, flex fuel ethanol vehicles that meet the applicable hydrocarbon (HC) emission limit for N1 Class III vehicles in column L2 of the table to paragraph 5.3.5.2 of Appendix A when tested on the ethanol (E75) reference fuel in paragraph 2 of Annex 10 of Appendix A, shall be deemed to meet the HC emission limit for this test on ethanol.

5.5.                                    In Table A to paragraph 5.2 of Appendix A, footnote 3 is amended to read “The ethanol (E75) reference fuel specified in paragraph 2 of Annex 10 of Appendix A shall be used for this test.”

5.6.                                    The Ethanol (E75) reference fuel specification in paragraph 2 of Annex 10 of Appendix A is amended to read:

Type: Ethanol (E75)

5.7.                                    For the purposes of calculating the Lambda value when tested at ‘high idle speed’ in accordance with Paragraph 5.3.7.3. of Appendix A on the ethanol (E75) reference fuel in paragraph 2 of Annex 10 of Appendix A:

-          the Atomic ratio of hydrogen to carbon shall be 2.61; and

-          the Atomic ratio of oxygen to carbon shall be 0.329.

5.8.                                    For the purposes of determining the total mass of Hydrocarbons emitted in accordance with paragraph 6.6.2. of Annex 4a of Appendix A, when tested on the ethanol (E75) reference fuel in paragraph 2 of Annex 10 of Appendix A, the density shall be 0.886 g/l.

5.9.                                    For the purposes of determining the correction for dilution air concentration in accordance with paragraph 6.6.4 of Annex 4a of Appendix A, when tested on the ethanol (E75) reference fuel in paragraph 2 of Annex 10 of Appendix A, the dilution factor shall be calculated as follows:

6.                                          ALTERNATIVE STANDARDS

6.1.                                    The technical requirements of United Nations Economic Commission for Europe Regulation No. 83 Uniform provisions concerning the approval of vehicles with regard to the emissions of pollutants according to engine fuel requirements, Revision 4, incorporating the 06 series of Amendments, are deemed to be equivalent to the technical requirements of this vehicle standard.

Compilation NOTES – note 1

This compilation of Vehicle Standard (Australian Design Rule 79/04 — Emission Control for Light Vehicles) 2011 includes all the instruments set out in the Table of Instruments.  The Table of Amendments provides a history of clauses that have been amended, inserted or deleted.

Table of Instruments

Table of Amendments

ad = added or inserted

am  = amended

del  = deleted or removed

rr  = removed and replaced

  = clause renumbered.  This takes the format of old no.  new no.