Motor Vehicle Standards (Used Imported Vehicle Report) Determination 2006 (No. 1)

 

 

I, JAMES ERIC LLOYD, Minister for Local Government, Territories and Roads, make this Determination under subsection 13D (2) of the Motor Vehicle Standards Act 1989.

Dated:   19 June 2006

[signed]

 

JIM LLOYD

Contents

Page

1 Name of Determination 

2 Commencement 

3 Revocation of the Motor Vehicle Standards (Used Imported Vehicle Report) Determination 2002 (2).

4 Definitions 

5  Vehicle inspection certificate 

Schedule 1 Vehicle inspection certificate 

1 Name of Determination

  This Determination is the Motor Vehicle Standards (Used Imported Vehicle Report) Determination 2006 (No. 1).

2 Commencement

  This Determination commences on the day after registration on the Federal Register of Legislative Instruments.

3                            Revocation of the Motor Vehicle Standards (Used Imported Vehicle Report) Determination 2002 (2).

Motor Vehicle Standards (Used Imported Vehicle Report) Determination 2002 (2) is revoked.

 Note:  The Motor Vehicle Standards (Used Import Vehicle Report) Determination 2002 (2) was made by the Parliamentary Secretary to the Minister for Transport and Regional Services on 12 December 2002 and notified in the Gazette on 18 December 2002.

4 Definitions

 (1) In this Determination:

Act means the Motor Vehicle Standards Act 1989.

ADR means the Australian Design Rules.

Full bump means when the suspension is fully compressed.

Plate location means the location of the Used Import Plate as required by the Motor Vehicle Standards (Placement of Used Import Plates) Determination 2004 (No.1) made under s13B of the Act in accordance with the grid locations specified in the Vehicle Inspection Manual as approved by the Administrator of Vehicle Standards on 9 December 2002.

vehicle identification number (VIN), for a vehicle, means a number:

(a)    corresponding to the vehicle identification number of the vehicle; and

(b)   stated on a used import plate that identifies the vehicle.

VIN location means the position on the vehicle, of the Vehicle Identification Number as required by clause 5.1 of ADR 61/02 in accordance with the grid locations specified in the Vehicle Inspection Manual as approved by the Administrator of Vehicle Standards on 9 December 2002.

 

 (2) Unless the contrary intention appears, a word or expression that is used in this Determination and in the Motor Vehicle Standards Regulations 1989 has the same meaning in this Determination as it has in those Regulations.

Note 1   The following terms are defined in the Act:

 registered automotive workshop

 used imported vehicle.

 

Note 2   The following terms are defined in the Motor Vehicle Standards Regulations 1989:

 Australian Design Rules

 make

 model

 RAW

 Register of Specialist and Enthusiast Vehicles

 RVCS participant number (defined in regulation 39)

 vehicle category

 vehicle inspection signatory (defined in regulation 39)

 

Note 1:  The following are defined terms in the ADRs

5 Vehicle inspection certificate

  For subsection 13D (2) of the Act, a report in relation to a used imported vehicle (to be known as a Vehicle Inspection Certificate) is to be in the form, and contain the information, set out in Schedule 1.

Schedule 1 Vehicle inspection certificate

(section 5)

 

 

 

 

Application Reference

 

RAWS Participant ID No      Your Document Reference No

 

 

Replacement Form 

 

  If applicable – to correct a previously     Replaced Form Document Reference No.

  submitted form:          

 

Vehicle Details

 

VIN

 

Model

 

Make

 

Model Code

 

Vehicle Category

 

VIN location

 

-

 

-

 

Build Date (MM/YYYY)

 

Used Import Plate Location

 

-

 

-

 

SEVS Entry Number

 

RAWS Schedule No.

 

Import Approval No

 

 

 

 

Variant Details

 

Variant Name

 

Tare Mass

 

Gross Vehicle Mass

 

Gross Combination Mass

 

Seating Options

 

 

 

 

Axle Code

 

Braked

Un-Braked

Max Towing Mass

 

 

 

Number of Doors

Side

Rear

B-Double Capable

 

Road Train Capable

 

 

 

 

Engine Details

 

Model

 

Number

 

 

 

Engine Number location

 

 

 

Capacity (cc)

Motive Power

NEP (kW)

NEP (rpm)

Fuel Injection/ Carburettor

Strokes & cycle

Induc-tion

 

 

 

 

 

 

 

 

 


Service Brakes

 

Brake System

Front

Rear

Actuation Type

Power Assisted?

Type

Nominal Diameter (mm)

Nominal Width (mm)

Type

Nominal

Diameter (mm)

Nominal

Width (mm)

 

 

 

 

 

 

 

 

 

Transmission

 

 Transmission    Forward  Forward Gears

 

Tyre and Rim Information

 

 

Tyre Designation

Rim Size and Profile

Rim Offset (mm)

Wheel Track (mm)

Front

 

 

 

 

Rear

 

 

 

 

 

Suspension Data  Major Dimensions

 

Wheel Centre to top of wheel arch

Unladen

 

Total Length

(mm)

Overall Width

(mm)

Height

(mm)

Wheel-Base (mm)

Ground Clearance

(mm)

Front (mm)

 

 

 

 

 

 

 

 

Rear (mm)

 

 

 

 

 

 

 

 

 

Equipment Affecting ADR Compliance

 

Air Conditioning

Antilock Brakes

Power Windows

Power Mirrors

 

 

 

 

Drivers Airbag

Passengers Airbag

Central locking

Other

 

 

 

 

 

Axle Load Ratings

 

Axle No

First front axle

Second front axle

First rear axle

Second rear axle

Third rear axle

Axle Load Rating (kg) for heaviest variant

 

 

 

 

 

 

Remarks

 

 

 

 

 

 

 


Incoming Vehicle Inspection Report

Document Reference No

 

Consumer Information Notice

 

Document Reference No

 

Completed Vehicle Report

 

Document Reference No

 

 

EVIDENCE TO DEMONSTRATE THAT THIS VEHICLE MEETS THE REQUIREMENTS

 

ADR Number

New

 Evidence

Specific Evidence

Document Reference

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Declaration

 

This declaration must be made before this Vehicle Inspection Certificate is transmitted to DOTARS.

 

I     (name of Vehicle Inspection Signatory)

certify that I have seen and inspected the vehicle identified in this Certificate and confirm that it has been modified in accordance with the evidence set out in this Certificate and in accordance with the Motor Vehicle Standards (Approval to Place Used Import Plates) Guidelines 2006 (No. 1).

 

Cross   to indicate agreement with the above statement.